Related Topics:
Capacitor Comprehensive Guide-
The relationship formula between capacitor and power supply voltage
The relationship between this charging current and the rate at which the capacitors supply voltage changes can be defined mathematically as: i = C (dv/dt), where C is the capacitance value of the c.
FAQs about The relationship formula between capacitor and power supply voltage
What are the components of a capacitive power supply?
Full-wave bridge rectifier circuit. Voltage regulator circuit. Power indicator circuit. A capacitive power supply has a voltage dropping capacitor (C1), this is the main component in the circuit. It is used to drop the mains voltage to lower voltage. The dropping capacitor is non-polarized so, it can be connected to any side in the circuit.
What is the relationship between charge current and supply voltage?
The relationship between this charging current and the rate at which the capacitors supply voltage changes can be defined mathematically as: i = C (dv/dt), where C is the capacitance value of the capacitor in farads and dv/dt is the rate of change of the supply voltage with respect to time.
How to calculate capacitance of a capacitor?
The following formulas and equations can be used to calculate the capacitance and related quantities of different shapes of capacitors as follow. The capacitance is the amount of charge stored in a capacitor per volt of potential between its plates. Capacitance can be calculated when charge Q & voltage V of the capacitor are known: C = Q/V
What happens when a capacitor reaches a peak?
The voltage across the capacitor matches the power supply voltage, so the current is large to build up charge on the capacitor plates. The closer the voltage gets to its peak, the slower it changes, meaning less current has to flow. When the voltage reaches a peak at point b, the capacitor is fully charged and the current is momentarily zero.
How do you calculate the charge of a capacitor?
C = Q/V If capacitance C and voltage V is known then the charge Q can be calculated by: Q = C V And you can calculate the voltage of the capacitor if the other two quantities (Q & C) are known: V = Q/C Where Reactance is the opposition of capacitor to Alternating current AC which depends on its frequency and is measured in Ohm like resistance.
What type of power supply uses a capacitive reactance?
This type of power supply uses the capacitive reactance of a capacitor to reduce the mains voltage to a lower voltage to power the electronics circuit. The circuit is a combination of a voltage dropping circuit, a full-wave bridge rectifier circuit, a voltage regulator circuit, and a power indicator circuit.
-
Relationship between capacitor and inductor
To better understand the differences between the two components, it will benefit you to first learn a bit more about each component individually. Things like their purpose, working principle, construction, etc. However, if you already have a knowledge of both components, you can skip straight to the capacitor vs inductor section. Capacitors are one of the three fundamental passive components used in electrical and electronic circuits (the other two being resistors and inductors). A capacitor is a two terminal passive component which has the. A capacitor is constructed using two metal plates which are separated by an insulating material known as the dielectricas seen in the. When a capacitor is connected to a power source (like a battery), it stores the received energy in the form of the electric field which we have just discussed. The amount of energy stored. The simplest form of a capacitor is two metal plates separated by a dielectricas we saw earlier. When a voltage is applied to a capacitor, an electron is added to one plate making it negatively.
[PDF Version]
FAQs about Relationship between capacitor and inductor
What are capacitors & inductors?
Capacitors and inductors are important components in electronic circuits and each of them serve unique functions. Capacitors store energy in an electric field, while inductors store energy in a magnetic field. They have different applications and characteristics, such as energy storage, filtering, and impedance matching.
Why do we use inductors over capacitors?
We opt for inductors over capacitors because inductors hold energy within a field whereas capacitors store energy in a field. Depending on the circuit's needs, like energy storage, filtering or impedance matching an inductor might be a choice, than a capacitor. What is the difference between resistor capacitor and inductor?
What are the characteristics of ideal capacitors and inductors?
Delve into the characteristics of ideal capacitors and inductors, including their equivalent capacitance and inductance, discrete variations, and the principles of energy storage within capacitors and inductors. The ideal resistor was a useful approximation of many practical electrical devices.
What are the properties of inductance and capacitance?
They also approximate the bulk properties of capacitance and inductance that are present in any physical system. In practice, any element of an electric circuit will exhibit some resistance, some inductance, and some capacitance, that is, some ability to dissipate and store energy.
Do inductors have capacitive effects?
In addition to the resistive non-idealities of inductors there could also be capacitive effects. These effects usually become important at high frequencies. Unless stated otherwise, these effects will be neglected in out analysis. The inductance L represents the efficiency of storing magnetic flux.
How do capacitors work?
Capacitors work by keeping pairs of opposite charges apart. The most basic design is the parallel plate capacitor, made of two metal plates separated by a gap. What is Inductor? An inductor is a component, in electronics that stores energy by creating a field when electricity flows through it.
-
Reactive Power Compensation Capacitor Selection
Having above information, it is possible to find fitting cubicle for the elements of the capacitor bank. Because the device is going to operate at the mains, where higher order harmonics are present, power capacitors must be protected by reactors. Each capacitor emits additional amount of heat as well as a reactor. The. The arrangement of the elements inside the enclosure should be easily available for maintenance and replacement, and each element should be clearly marked according to the technical. The next step is to chose appropriate power capacitors. It means, that one needs to pay attention to its rated voltage and power. Since the. The short circuit protection of the capacitors is provided by the switch disconnectors. For the capacitors the fuse link rated current should be 1.6 time of the rated reactive current of. The last step is to select the protection of the capacitors as well as the contactors. In order to do so, one has to skim the catalogue cards of the manufacturers. Contactors for the.
[PDF Version]
FAQs about Reactive Power Compensation Capacitor Selection
Can capacitive reactive power be used to regulate voltage?
This article presents an efficient voltage regulation method using capacitive reactive power. Simultaneous operation of photovoltaic power systems with the local grids induces voltage instabilities in the distribution lines. These voltage fluctuations cross the allowable limits on several occasions and cause economic losses.
What is reactive power compensation panel?
Excellent. The aim of project called „Reactive power compensation panel” was to design capacitor bank with rated power of 200kVar and rated voltage of 400V adapted for operation with mains, where higher order harmonics are present. The capacitor bank was to be power capacitor based with automatic control by power factor regulator.
How is capacitive reactive power produced?
The capacitive reactive power is generated through the capacitance producing devices serially or shunt connected to a load , , . A significant amount of studies was devoted to the methods to produce reactive power, such as DSTATCOMs, , , STATCOM, , , and real electrical capacitors .
Is reactive power compensation an optimization problem?
Mathematical formulation The reactive power compensation has been analyzed mainly as an optimization problem restricted to a single objective, which would provide a single optimal solution with a priority approach based on the adequate selection of capacity and location of capacitor banks.
How to choose series of capacitors for PF correction?
Considering power capacitor with rated power of 20 kvar and rated voltage of 440V supplied by mains at Un=400V. This type of calculation is true, if there is no reactor connected in series with capacitor. Once we know the total reactive power of the capacitors, we can choose series of capacitors for PF correction.
What is the solution for concentrated reactive power compensation?
Solution 1 (S1): concentrated reactive power compensation with capacitor banks. Solution 2 (S2): distributed reactive power compensation with capacitor banks. Solution 3 (S3): concentrated reactive power compensation with harmonic filters. Solution 4 (S4): distributed reactive power compensation with harmonic filters.
-
Tantalum electrolytic capacitor model
The of a component is a property that indicates how well a component performs its function in a time interval. It is subject to a and can be described qualitatively and quantitatively; it is not directly measurable. The reliability of electrolytic capacitors are empirically determined by identifying the in production-accompanying, see.
FAQs about Tantalum electrolytic capacitor model
What is a tantalum electrolytic capacitor?
Tantalum electrolytic capacitors have been on the market for more than half a century, in a range of applications. However, the most common design uses MnO 2 as the electrolyte, which can be thermodynamically unstable and, upon failure, can damage the circuit.
How are tantalum capacitors made?
The pellet is next coated with graphite, followed by a layer of metallic silver, which provides a conductive surface between the pellet and the leadframe. Molded chip tantalum capacitor encases the element in plastic resins, such as epoxy materials. After assembly, the capacitors are tested and inspected to ensure long life and reliability.
What are Talum electrolytic capacitors?
Tantalum electrolytic capacitors are the preferred choice in applications where volumetric efficiency, stable electrical parameters, high reliability, and long service life are primary considerations.
Why is the capacitance of a tantalum capacitor high?
As the dielectric constant of the tantalum pentoxide is high, the capacitance of a tantalum capacitor is high if the area of the plates is large: Tantalum capacitors contain either liquid or solid electrolytes. In solid electrolyte capacitors, a dry material (manganese dioxide) forms the cathode plate.
Are solid tantalum capacitors a good investment?
Solid tantalum capacitor manufacturers can make improvements in physical design and materials that reduce the overall ESR of the capacitor. These lower ESR capacitors will lead to reductions in heat generation within the capacitor, thus improving overall circuit efficiency and long-term reliability.
Are solid tantalum capacitors a good choice for surface mount assembly?
The stability and resistance to elevated temperatures of the tantalum / tantalum oxide / manganese dioxide system make solid tantalum capacitors an appropriate choice for today's surface mount assembly technology.
-
Semiconductor capacitor production process
The process of manufacturing capacitors involves several stages, including material preparation, electrode formation, winding, and encapsulation.
FAQs about Semiconductor capacitor production process
What is the manufacturing process of ceramic capacitor?
Manufacturing process of ceramic capacitor, principal ingredient of the ceramic capacitor is ceramic powder, where ceramic material acts as a dielectric. Due to their unique material properties, technical ceramics are considered to be one of the most efficient materials of our time.
How are capacitors created in MOS semiconductor processes?
Learn how capacitors are created in MOS semiconductor processes. In semiconductor processes, the oxides providing isolation between layers are designed to give minimum stray capacitance. These oxides separate the metal interconnect from the silicon and different metal interconnect layers from each other.
How are capacitors made?
The manufacturing process for capacitors typically involves several steps, including cutting and forming the metal foils, applying the dielectric material, and winding the foils and dielectric together. The winding process creates the capacitor's structure, which can be cylindrical or rectangular in shape.
What is capacitor production?
Capacitor production is a complex process that requires precision and attention to detail. The first step in capacitor production is selecting the appropriate materials. Capacitors can be made from a variety of materials, including ceramic, tantalum, and aluminum.
What materials are used in capacitor production?
The raw materials used in capacitor production include metal foils, dielectric materials, and electrolytes. The metal foils are typically made of aluminum or tantalum, while the dielectric materials can be ceramic, plastic, or paper. Electrolytes are used in certain types of capacitors, such as electrolytic capacitors.
What is the first step in capacitor production?
The first step in capacitor production is selecting the appropriate materials. Capacitors can be made from a variety of materials, including ceramic, tantalum, and aluminum. Each material has its own unique properties and advantages, so it's important to choose the right one for the job.
-
Capacitor battery replacement
The reason why capacitors cannot be used as a replacement for batteries is due to their limited energy storage duration, rapid voltage decay, and lower energy density.
FAQs about Capacitor battery replacement
Will supercapacitor replace batteries?
To summarize, the Supercapacitor technology would still have to evolve in a big way before actually replacing batteries although the former offers a promising alternative to batteries.
Can a capacitor replace a battery?
It is common knowledge that capacitors store electrical energy. One could infer that this energy could be extracted and used in much the same way as a battery. Why can capacitors then not replace batteries? Conventional capacitors discharge rapidly, whereas batteries discharge slowly as required for most electrical loads.
What is the difference between a car battery and a capacitor?
Car batteries use chemical reactions within their cells to store electrical energy, allowing them to release energy over longer periods. In contrast, capacitors consist of two conductive plates separated by an insulating material, enabling them to charge and discharge energy rapidly.
How much energy does a capacitor hold?
Capacitors can typically hold only a fraction of the energy that a standard lead-acid battery can store. For instance, a typical car battery might store about 40 to 100 amp-hours, while an automotive capacitor might only hold a few farads of charge, equating to much less energy.
How to use a capacitor in a car?
When using a capacitor in your car, it is crucial to take specific safety precautions to prevent accidents and damage. Disconnect the battery before installation. Use appropriate ratings for voltage and capacitance. Avoid short-circuiting the capacitor. Use insulated tools while working. Wear protective gear (gloves, goggles).
How does a capacitor work?
Capacitor works by holding electric field between electrodes, unlike lead-acid cell which stores energy in chemical reactions between electrolyte and plates. Are there any modifications you have to do in order to use a capacitor instead of a battery? Battery is great at stabilizing voltage, capacitor just holds any voltage you connect it to.
-
Causes of fan capacitor failure
Why Do So Many Capacitors Fail?1. Overheating Capacitors fail if they are in direct sun for too long or if they run for too long, contributing to failure in the air conditioner fan capacitor. Vibration, acceleration & shock.
FAQs about Causes of fan capacitor failure
What causes a capacitor to fail?
In addition to these failures, capacitors may fail due to capacitance drift, instability with temperature, high dissipation factor or low insulation resistance. Failures can be the result of electrical, mechanical, or environmental overstress, "wear-out" due to dielectric degradation during operation, or manufacturing defects.
Why do paper and plastic film capacitors fail?
Paper and plastic film capacitors are subject to two classic failure modes: opens or shorts. Included in these categories are intermittent opens, shorts or high resistance shorts. In addition to these failures, capacitors may fail due to capacitance drift, instability with temperature, high dissipation factor or low insulation resistance.
Is it easy to fix a failing air conditioner capacitor?
As long as you catch the failing capacitor early, it's relatively easy and inexpensive to fix. If the air conditioner continues to run with failing capacitors, it can cause much more serious and expensive issues down the road. See Also: When Should I Replace My HVAC?
What causes a capacitor to overheat?
Underlying Issues: This overheating can be due to internal failure within the capacitor or external factors such as a malfunctioning component in the circuit. It's a sign that the capacitor has been operating under stress and may have already failed or is close to failing.
What happens if a capacitor isn't working properly?
When a capacitor isn't working properly, whatever motor it's attached to can get overheated and burn out. Instead of replacing a capacitor, you could end up having to replace the fan motor or the compressor. This could even result in the entire air conditioner needing replaced. You definitely don't want that!
Why is capacitor failure important?
Capacitor failure is a significant concern in electronics, as these components play a critical role in the functionality and longevity of electronic circuits. Understanding the nuances of capacitor failure is essential for diagnosing issues in electronic devices and implementing effective solutions.
-
What color are the leads in a capacitor
The grey-colored area on the casing corresponds to the negative lead, with the opposite end being positive. If the capacitor is packaged, the positive terminal is usually marked with a “+” symbol, o.
FAQs about What color are the leads in a capacitor
What do the coloured bands on a capacitor mean?
These coloured bands represent the capacitance value as per the colour code including voltage rating and tolerance. Sometimes the actual values of capacitance, voltage or tolerance are marked onto the body of a capacitor in the form of alphanumeric characters.
What are the color bands of capacitance?
In the following tables, the first three color bands show the value of capacitance, the fourth band as tolerance in percentage and the fifth band shows the temperature coefficient. For example: 1st Color Band = First Number of Value of Capacitor. 2nd Color Band = Second Number of value of Capacitor.
What is an example of a capacitor colour code?
An example of the use of capacitor colour codes is given as: The Capacitor Colour Codes system was used for many years on unpolarised polyester and mica moulded capacitors. This system of colour coding is now obsolete but there are still many “old” capacitors around.
How do you know if a capacitor is capacitive?
There are two common ways to know the capacitive value of a capacitor, by measuring it using a digital multimeter, or by reading the capacitor colour codes printed on it. These coloured bands represent the capacitance value as per the colour code including voltage rating and tolerance.
What are the different types of capacitor markings & codes?
The various parameters of the capacitors such as their voltage and tolerance along with their values is represented by different types of markings and codes. Some of these markings and codes include capacitor polarity marking; capacity colour code; and ceramic capacitor code respectively.
What does the marking on a capacitor mean?
Every capacitor has a special marking printed on its body. It represents the value or colour code of capacitor. There are different types of capacitor and each has its specified capacitance value, voltage rating, temperature range, tolerance and life time. But most of the capacitors have their value and their voltage printed on their body.
-
Capacitor Manufacturers in Tuvalu
A is a passive device on a circuit board that stores electrical energy in an electric field by virtue of accumulating electric charges on two close surfaces insulated from each other. This is a list of known manufacturers, their headquarters country of origin, and year founded. The oldest capacitor companies were founded over 100 years ago. Most older companies were founded during the era, which includes the era and post war era. As the de.
FAQs about Capacitor Manufacturers in Tuvalu
Who is CorCap capacitor?
At Corcap Capacitor, we are passionate about delivering cutting-edge capacitor solutions that elevate performance, reliability, and innovation. As a leading capacitor manufacturing company, we combine decades of industry experience with a commitment to excellence, offering our customers unparalleled expertise and customized solutions. Products.
What is a capacitor & how does it work?
A capacitor is a passive device on a circuit board that stores electrical energy in an electric field by virtue of accumulating electric charges on two close surfaces insulated from each other. This is a list of known capacitor manufacturers, their headquarters country of origin, and year founded.
Why are capacitor manufacturers important?
Most older companies were founded during the AM radio era, which includes the World War II era and post war era. As the demand for advanced electronics continues to grow, the role of capacitor manufacturers becomes increasingly vital, supporting crucial domains like consumer electronics, power systems, automotive technology, and telecommunications.
What is a capacitor in physics?
Definition of Capacitor A capacitor is an element that stores electricity and electrical energy (potential energy). A conductor surrounded by another conductor, or a conductor in which all the electric field lines emitted by one conductor terminate in the other conductor, is called a capacitor.
Who are the leading dual MPP washing machine capacitor manufacturers?
Washing Machine Capacitor Manufacturers and Suppliers in India Capacitors is one of the leading Dual MPP Washing Machine Capacitor manufacturers. Social. Follow us on social media and get our latest news & updates.
What type of conductor is a capacitor?
Two conductors in close proximity to each other with a layer of non-conducting insulating medium sandwiched between them, this constitutes a capacitor. A capacitor stores charge when a voltage is applied between the two extreme plates of the capacitor.
-
Korea Super Farad Energy Storage Capacitor
A team of researchers in South Korea has developed an advanced supercapacitor that delivers not only high power density but also a record-breaking energy density of 418 Wh/kg. Even more impressively, it maintains stable performance after more than 100,000 charge-discharge cycles.
-
Water enters the bottom of the lithium battery
When water infiltrates a lithium battery, it instigates a series of detrimental reactions that can lead to heat generation, hydrogen gas release, and potential fire hazards.
FAQs about Water enters the bottom of the lithium battery
How does water affect a lithium battery?
Part 2. Lithium battery and water reactions Water can trigger hazardous reactions in lithium batteries due to the highly reactive nature of lithium with moisture. When water infiltrates a lithium battery, it instigates a series of detrimental reactions that can lead to heat generation, hydrogen gas release, and potential fire hazards.
Can lithium ion batteries catch fire if submerged in water?
Fire Hazard Lithium-ion batteries are highly susceptible to catching fire when submerged in water. The water can cause the battery to short circuit, and as the battery heats up, it may ignite. Even worse, water cannot extinguish a lithium battery fire. Instead, it can exacerbate the flames, making the situation far more dangerous.
Can lithium-ion batteries be submerged in water?
The interaction between lithium-ion batteries and water can lead to dangerous reactions, including short circuits, chemical fires, and even explosions. This article explores why submerging lithium-ion batteries in water is hazardous and what precautions should be taken to prevent potential disasters.
What happens if a lithium ion battery gets wet?
The lithium ion battery submerged in water will behave differently. If your battery's air tightness fails, water entry into lithium batteries can reduce performance or short-circuit. What Happens When Lithium Batteries Get Wet? When a battery comes into contact with water, internal acids leak, damaging the battery.
Can lithium ion batteries withstand water?
Lithium batteries, including popular variants like lithium-ion (Li-ion) and lithium polymer (LiPo) batteries, are generally not designed to withstand exposure to water. Water can act as a conductor, potentially creating a short circuit between the battery terminals.
Can a lithium battery be submerged in water?
Submerging a lithium battery in water is not recommended since it may damage the sealing on the case, allowing the batteries to become wet. Whenever water enters into the batteries, it can cause fast oxidation of the metal connections inside the cells, reducing the overall efficiency of the battery pack.
-
What is the name of the solar panels for the whole family
There are nine main types of solar panels: monocrystalline, polycrystalline, thin film, transparent, Concentrator Photovoltaics (CPV), Passivated Emitter and Rear Contact (PERC), perovskite, solar tile, and solar thermal. Each of these panels comes with its own advantages and disadvantages, and will suit some homes better. When you're trying to pick the best solar panelsfor you, you'll need to consider a few factors. If aesthetics is most important to you, you should look. The solar panel industry is always developing and changing for the better, as the older models are supplanted by new, more efficient versions. When it comes to domestic solar panels, homeowners can choose between polycrystalline, monocrystalline, and thin film – the right type for you will depend entirely on your priorities. Want an easy way to find the perfect set.
[PDF Version]
-
Marshall Islands Super Smart Capacitor Manufacturer
The world's highest energy density 2. 7V supercapacitors, UL 810A-certified for rapid charge-discharge, extreme durability, and minimal degradation over millions of cycles. Designed for efficiency and scalability, our cells power everything from EVs to grid and renewable energy storage.
-
Is the bottom of the lead-acid battery afraid of getting wet
Key Takeaways – The short answer is that it depends on the type of battery. Most Lead-acid batteries are relatively resistant to water, although prolonged exposure can still cause problems.
FAQs about Is the bottom of the lead-acid battery afraid of getting wet
What happens if a lead acid battery runs out of water?
If a lead acid battery runs out of water, meaning the electrolyte has fully dried up or the battery has been tilted or stored upside down causing the electrolyte to spill, this is the main concern.
Does flooded electrolyte lead acid battery cause thermal runaway?
Flooded electrolyte lead acid batteries do not cause thermal runaway because the electrolyte, which acts as a coolant in these batteries, helps prevent such an occurrence. Designers of flooded electrolyte lead acid batteries do not face the thermal runaway problems that are common in sealed maintenance free (SMF) or valve regulated lead acid (VRLA) batteries.
Can we remove acid from flooded electrolyte lead acid batteries?
A lead acid battery, including flooded electrolyte types, should not have its acid completely removed once it has been filled and charged. It is important not to remove the acid. A lead acid battery consists of several major components, including the positive electrode, negative electrode, sulphuric acid, separators, and tubular bags.
What happens when a battery is drained of acid?
When a lead acid battery is drained of its acid, the wet moist negative electrodes come in contact with atmospheric oxygen, triggering an exothermic reaction that releases heat and discharges the negative plates (electrodes), oxidizing the sponge lead to lead oxide.
What is a lead acid battery?
A lead acid battery is a type of rechargeable battery that has positive and negative plates fully immersed in electrolyte, which is dilute sulphuric acid.
Are lead-acid batteries resistant to water?
Most Lead-acid batteries are relatively resistant to water, although prolonged exposure can still cause problems. By contrast, batteries commonly used in laptops and smartphones, and other types of batteries (like Lithium-ion batteries) are much more vulnerable to water damage.
-
Papua New Guinea Super Farad Capacitor Manufacturer
Brian Bell Trade Electrical is part of the Brian Bell Group, Papua New Guinea's foremost retailer, wholesaler and distributor. Copyright 2025 Brian Bell Group.
-
Capacitor Plate Circuit
Explore how a capacitor works! Change the size of the plates and add a dielectric to see how it affects capacitance. Change the voltage and see charges built up on the plates.
FAQs about Capacitor Plate Circuit
How do capacitors store electrical charge between plates?
The capacitors ability to store this electrical charge ( Q ) between its plates is proportional to the applied voltage, V for a capacitor of known capacitance in Farads. Note that capacitance C is ALWAYS positive and never negative. The greater the applied voltage the greater will be the charge stored on the plates of the capacitor.
How does a capacitor work?
An electric field forms across the capacitor. Over time, the positive plate (plate I) accumulates a positive charge from the battery, and the negative plate (plate II) accumulates a negative charge. Eventually, the capacitor holds the maximum charge it can, based on its capacitance and the applied voltage.
What is a capacitance of a capacitor?
Capacitance is defined as being that a capacitor has the capacitance of One Farad when a charge of One Coulomb is stored on the plates by a voltage of One volt. Note that capacitance, C is always positive in value and has no negative units.
What is a capacitor used for?
Capacitor Definition: A capacitor is defined as a device with two parallel plates separated by a dielectric, used to store electrical energy. Working Principle of a Capacitor: A capacitor accumulates charge on its plates when connected to a voltage source, creating an electric field between the plates.
What is a capacitor plate used for?
Capacitors with a flexible plate can be used to measure strain or pressure. Industrial pressure transmitters used for process control use pressure-sensing diaphragms, which form a capacitor plate of an oscillator circuit.
Why does a capacitor have a higher capacitance than a plate?
Also, because capacitors store the energy of the electrons in the form of an electrical charge on the plates the larger the plates and/or smaller their separation the greater will be the charge that the capacitor holds for any given voltage across its plates. In other words, larger plates, smaller distance, more capacitance.